Vertical axis wind turbine

Here's a start-up called Icewind that is building a new type of funky wind turbine designed to perform well in low-wind conditions but also to slow itself down in high-winds, preventing it from catching on fire or ripping apart.

Transparent solar panels

With support from the National Science Foundation (NSF), Michigan State University materials scientist and chemical engineer Richard Lunt and his team are developing transparent solar panels that could be retrofit to cover existing windows instead of replacing them. With the square footage of glass that's on skyscrapers and other buildings, the tremendous potential for energy and cost savings is clear

Molecular solar thermal energy

Storing of solar energy is major challenge & key point of reserch among scientist. 

Kasper Moth Poulsen from chalmers university of technology had developed a way called molecular solar thermal energy storage to store energy of sun into the molecular bonds & again utilise them.

Solving the global cooking problem with solar energy.

In many rural parts of world still cooking through burning woods & fossil fuel is major cause of pollution & causes sever health issues.

Here is the solution inovated by students of ISEE with the use of clean solar energy

Biogas energy

WHAT IS BIOGAS ?

The term “biogas” is used for a gas produced by anaerobic fermentation of different forms of organic matter. This anaerobic process is driven by different varieties of bacteria, in anaerobic digester tanks this is usually at a temperature of 30 – 40° C.

FEEDSTOCK FOR PRODUCTION OF BIOGAS

Typical feedstock’s for biogas production are manure and sewage, residues of crop production (i.e., straw), the organic fraction of the waste from cities and municipalities, be it sewage sludge, waste from the food industry or collected from household organic waste bins, as well as energy crops including maize and grass silage. The process itself occurs in airtight biogas digesters without oxygen.  The rate of the process depends on the feedstock and several other parameters. The digestion time varies from several hours (for sugars, and alcohol) to several weeks (in case of hemicelluloses, fat, and protein).  

TYPE	Nm3  biogas
1 milking cow 20m³ liquid manure/a	500
1 pig 1.5 – 6 m³ liquid manure/a	42-168
1 cattle (beef) 3 -11t solid manure/a	240 – 880
100 chicken -1,8m³ dry litter	242
Maize silage 40 -60 green weight/ha	7040 - 10560
Grass 24 – 43 t fresh matter/ha	4118 - 6811

 

COMPOSITION OF BIOGAS

During this biological process a major portion of the carbon compounds are converted to CH4, CO2 and water. Biogas consists mainly of methane, carbon dioxide, and some other minor components.

Composition of bio gas

MATTER	%
CH4	50-75
CO2	25-45
H20	2-7
N2	<2
O2	<2
NH3,H2,H2S,trace gases

 

WORKING OF BIO GAS PLANT

Manure and sewage, residue of crop, the organic waste from cities and municipalities are collected together in preliminary tank & from there they are disposed into fermenter.

Fermenter or digester is a large cylindrical container with a conical or dome shape at top in which temperature is maintained at 30-40 degree in which anaerobic fermentation occurs which produce biogas.

This biogas is heated & supplied to CHP plant which contain a gas operated engine or motor coupled with a generator which produces electrical power which is delivered to grid.

Biogas is directly used as a fuel in gas operated auto mobs or for cooking at home.

REASON FOR SLOW DEVELOPMENT

Reasons for the slow deployment of biogas include: a lack of information about the possibilities of biogas, a lack of a trained labor force, high capital cost for the setting up of commercial plants, generally inadequate and unreliable government support policies and the competition of natural gas as a cheaper alternative in many parts of the world.

ADVANTAGE OF BIOGAS ENERGY

A specific advantage of biogas technology is in the utilization of organic wastes and other organic byproducts for energy production, as opposed to disposal via landfills, which inevitably leads to further emissions of greenhouse gases by the process of slow decomposition.

Reference : "WBA factsheet-Biogas- an important Renewable energy source"

Solar Cell Physics

Solar, or photovoltaic (PV), cells are electronic devices that essentially convert the solar energy of sunlight into electric energy or electricity. The physics of solar cells is based on the same semiconductor principles as diodes and transistors, which form the building blocks of the entire world of electronics.

In the later part of the century, physicists discovered a phenomenon: when light is incident on liquids or metal cell surfaces, electrons are released. However, no one had an explanation for this bizarre occurrence. At the turn of the century, Albert Einstein provided a theory for this which won him the Nobel Prize in physics and laid the groundwork for the theory of the photoelectric effect. Figure 1 shows the photoelectric effect experiment. When light is shone on metal, electrons are released. These electrons are attracted toward a positively charged plate, thereby giving rise to a photoelectric current. Einstein explained the observed phenomenon by a contemporary theory of quantized energy levels, which was previously developed by Max Planck. The theory described light as being made up of miniscule bundles of energy called photons. Photons impinging on metals or semiconductors knock electrons off atoms. In the 1930s, these theorems led to a new discipline in physics called quantum mechanics, which consequently led to the discovery of transistors in the 1950s and to the development of semiconductor electronics.

                                                                                fig 1

Most solar cells are constructed from semiconductor material, such as silicon (the fourteenth element in the Mendeleyev table of elements). Silicon is a semiconductor that has the combined properties of a conductor and an insulator. Metals such as gold, copper, and iron are conductors; they have loosely bound electrons in the outer shell or orbit of their atomic configuration. These electrons can be detached when subjected to an electric voltage or current. On the contrary, atoms of insulators, such as glass, have very strongly bonded electrons in the atomic configuration and do not allow the flow of electrons even under the severest application of voltage or current. Semiconductor materials, on the other hand, bind electrons midway between that of metals and insulators. Semiconductor elements used in electronics are constructed by fusing two adjacently doped silicon wafer elements. Doping implies impregnation of silicon by positive and negative agents, such as phosphor and boron. Phosphor creates a free electron that produces so-called N-type material. Boron creates a “hole,” or a shortage of an electron, which produces so-called P-type material. Impregnation is accomplished by depositing the previously referenced dopants on the surface of silicon using a certain heating or chemical process. The N-type material has a propensity to lose electrons and gain holes, so it acquires a positive charge. The P-type material has a propensity to lose holes and gain electrons, so it acquires a negative charge. When N-type and P-type doped silicon wafers are fused together, they form a PN junction. The negative charge on P-type material prevents electrons from crossing the junction, and the positive charge on the N-type material prevents holes from crossing the junction. A space created by the P and N, or PN, wafers creates a potential barrier across the junction. This PN junction, which forms the basic block of most electronic components, such as diodes and transistors, has the following specific operational uses when applied in electronics:

In diodes, a PN device allows for the flow of electrons and, therefore, current in one direction. For example, a battery, with direct current, connected across a diode allows the flow of current from positive to negative leads. When an alternating sinusoidal current is connected across the device, only the positive portion of the waveform is allowed to pass through. The negative portion of the waveform is blocked. In transistors, a wire secured in a sandwich of a PNP-junction device (formed by three doped junctions), when properly polarized or biased, controls the amount of direct current from the positive to the negative lead, thus forming the basis for current control, switching, and amplification, as shown in Fig 2

fig 2

 

In light-emitting diodes (LEDs), a controlled amount and type of doping material in a PN-type device connected across a dc voltage source converts the electric energy to visible light with differing frequencies and colors, such as white, red, blue, amber, and green. In solar cells, when a PN junction is exposed to sunshine, the device converts the stream of photons (packets of quanta) that form the visible light into electrons (the reverse of the LED function), making the device behave like a minute battery with a unique characteristic voltage and current, which is dependent on the material dopants and PN-junction physics. This is shown in Fig 3

The bundles of photons that penetrate the PN junction randomly strike silicon atoms and give energy to the outer electrons. The acquired energy allows the outer electrons to break free from the atom. Thus, the photons in the process are converted to electron movement or electric energy as shown in Figure 1.4. It should be noted that the photovoltaic energy conversion efficiency is dependent on the wavelength of the impinging light. Red light, which has a lower frequency, produces insufficient energy, whereas blue light, which has more energy than needed to break the electrons, is wasted and dissipates as heat.

 

fig 3

 

Wind Energy

Wind is a form of solar energy and is a result of the uneven heating of the atmosphere by the sun, the irregularities of the earth's surface, and the rotation of the earth.

• TYPES OF WIND TURBINES

Modern wind turbines classify into two basic groups: the horizontal-axis  and the vertical-axis design. Horizontal-axis wind turbines typically either have two or three blades. These three-bladed wind turbines are operated "upwind," with the blades facing into the wind.

• SIZES OF WIND TURBINES

Utility-scale turbines range in size from 100 kilowatts to as large as several megawatts. Larger wind turbines are more cost effective and are grouped together into wind farms, which provide bulk power to the electrical grid. In recent years, there has been an increase in large offshore wind installations in order to harness the huge potential that wind energy,

• How does a turbine generate electricity?

A turbine is a machine that spins around in a moving fluid (liquid or gas) and catches some of the energy passing by. All sorts of machines use turbines, from jet engines to hydroelectric power plants and from diesel railroad locomotives to windmills. Even a child's toy windmill is a simple form of turbine.

The huge rotor blades (propellers) on the front of a wind turbine are the "turbine" part. As wind passes by, the kinetic energy (energy of movement) it contains makes the blades spin around (usually quite slowly). The blades have a special curved shape so they capture as much energy from the wind as possible.

Although we talk about "wind turbines," the turbine is only one of the three main parts inside these giant machines. The second part is a gearbox whose gears convert the slow speed of the spinning blades into higher-speed rotary motion—turning the drive shaft quickly enough to power the electricity generator.

The generator is the third main part of a turbine and it's exactly like an enormous, scaled-up version of the dynamo on a bicycle. When you ride a bicycle, the dynamo touching the back wheel spins around and generates enough electricity to make a lamp light up. The same thing happens in a wind turbine, only the "dynamo" generator is driven by the turbine's rotor blades instead of by a bicycle wheel, and the "lamp" is a light in someone's home dozens of miles away.